Smapudden bridge over a river, protective coating project
Common questions

Jotun industrial protective coatings FAQ

Twenty-nine questions in four groups: selection and systems, application and parameters, documents and support, purchasing and delivery. Each answer gives wording you can use directly.

China-based distributor of Jotun industrial protective coatings — supplied from the China production base to projects worldwide.

Selection and systems

How are Jotun industrial protective coatings selected as a system? What does each of the primer, intermediate coat and topcoat do?

Protective coatings are built up in layers. The primer carries adhesion, and in zinc-rich systems it also provides cathodic protection through the sacrificial action of the zinc dust (zinc-rich epoxy and inorganic zinc silicate belong to this group). The intermediate coat builds total film thickness and lengthens the path that moisture and chlorides must travel before they reach the substrate. The topcoat carries weather resistance, colour and gloss, and sets the repaint interval for the asset. The higher the corrosivity category and the longer the design life, the more coats and the thicker the total system. Send us the component, the service environment and the design life, and we can recommend the system and the grades.

Zinc-rich epoxy or inorganic zinc silicate: how to choose?

Both rely on zinc dust for cathodic protection; they differ in film properties and application requirements.Inorganic zinc silicate withstands higher temperatures and resists solvents better, and suits tanks, pipelines and high-temperature areas, but demands stricter surface preparation (blasting to Sa2.5 or better) and recoat intervals; Zinc-rich epoxy is more forgiving to apply, takes a wider range of topcoats and is more common on general steel structures. Inorganic zinc silicate should generally not be used on patched old coating or where only hand or power tool cleaning is possible.

Is an intermediate coat essential? Can a topcoat go directly on the primer?

For conventional steel structures with low corrosivity and a short design life, primer plus topcoat in two coats is sufficient. Coastal, chemical and offshore C4 and C5 environments are normally designed as three-coat systems; the intermediate coat both builds total film thickness and reduces the risk of pinholes in the topcoat. Saving one coat saves little in material cost, but insufficient total film thickness shortens the repaint cycle noticeably.

Acrylic polyurethane or polysiloxane for the topcoat?

Acrylic polyurethane is the mainstream choice for industrial corrosion protection: good weather resistance and colour/gloss retention, a mature application process and moderate cost. Polysiloxane offers stronger weathering performance and suits bridges, offshore structures and architecturally demanding projects that require very long repaint intervals. Most industrial buildings and steel structure projects are adequately served by polyurethane.

Can a new coat go straight over an old coating?

Three things must first be established: the old coating type, its adhesion, and whether chalking, blistering or flaking is present.Coatings of the same type (epoxy over epoxy, for example) adhere well and can be overcoated after cleaning; Where the type differs or the old coating has failed over large areas, remove back to substrate and redo as a complete system. Before application, a small adhesion test is advisable, or a solvent rub to establish whether the old coating is epoxy or polyurethane.

How is shop primer compatibility with the final system handled?

Shop primers (temporary protective coatings) are usually inorganic zinc silicate or zinc-rich epoxy; what matters is that they can be overcoated by the subsequent coats without causing intercoat problems. The principle is to confirm the type and thickness of the shop primer, complete surface cleaning before overcoating (sweep blasting or high-pressure water washing to remove salts) and schedule the work within that product's overcoating window. Where shop primer is heavily rusted or incompatible with later coats, blast it off.

Which systems are used for tank interiors, buried pipelines and other special areas?

It depends on the medium and the environment: crude and refined product tank linings are usually epoxy; chemical media require selection by chemical resistance; food and potable water tanks carry additional hygiene requirements. Buried pipelines are usually coated with solvent-free or fusion-bonded epoxy, together with cathodic protection. These areas carry the strictest requirements for surface preparation grade, residual salt and film thickness measurement; the system should be determined separately by medium and design specification.

Inside a large steel structure

Selection starts from the service conditions, not the model number

The corrosivity category, operating temperature, component type and design life determine how primer, intermediate coat and topcoat are combined.

Sales and technical support

Contact us for full support

We supply and export Jotun industrial coatings made in China. Get in touch.

WeChat QR code
Scan to add us on WeChat